2021 Audi A4 / S4 — Owner's Manual – Page #267

Posted on 12 Oct, 2020
Model: 2021 Audi A4 / S4
Pages: 304


File size: 108 MB

Download Manual

Online Viewer
8W1012721BC
Emergency
assistance
bracket
on
the
jack
@)
completely
covers
the
notch
on
the
vehicle.
>
Align
the
vehicle
jack
so
the
bracket
(@)
covers
the
notch
and
the
base
(2)
is
flat
on
the
ground.
The
base
@)
must
be
directly
under
the
mount-
ing
point
@.
>
Mount
the
crank
on
the
vehicle
jack:
insert
the
crank
into
the
opening
on
the
handwheel.
Turn
the
crank
to
the
left
or
right
to
secure
it.
>
Continue
raising
the
vehicle
jack
with
the
crank
until
the
wheel
lifts
off
the
ground
slightly.
ZA
WARNING
—To
reduce
the
risk
of
injury,
make
sure
no
one
is
in
the
vehicle
before
raising
it.
Make
sure
the
vehicle
jack
is
stable.
The
risk
of
injury
is
increased
when
the
ground
is
slippery
or
soft,
because
the
vehicle
jack
could
slide
or
sink.
Only
raise
your
vehicle
with
the
vehicle
jack
provided
by
the
factory.
If
you
use
a
vehicle
jack
designed
for
another
vehicle,
your
vehi-
cle
could
slip
and
cause
injury.
Position
the
vehicle
jack
only
at
the
desig-
nated
mounting
points
on
the
side
sill
and
align the
jack.
Otherwise,
the
vehicle
jack
could
slip
and
cause
an
injury
if
it
does
not
have
sufficient
hold
on
the
vehicle.
—To
reduce
the
risk
of
injury,
do
not
raise
any
other
vehicles
or
other
loads using
the
vehi-
cle
jack
provided
by
the
factory.
To
reduce
the
risk
of
an
accident,
never
start
the
engine
when
the
vehicle
is
raised.
—To
reduce
the
risk
of
injury,
no
work
should
be
performed
under
the
vehicle
while
it
is
raised.
()
Note
Do
not
lift
the
vehicle
by
the
sill.
Position
the
vehicle
jack only
at
the
designated
mounting
points
on
the
side
sill.
Otherwise,
your
vehicle
could
be
damaged.
Removing
and
installing
a
wheel
|
B8K-1479
Fig.
178
Wheel:
alignment
pin
in
the
top hole
Removing
a
wheel
>
Remove
the top
wheel
bolt
completely
using
the
hex
socket
in
the
screwdriver
handle
from
the
vehicle
tool
kit
>
fig.
177
and
place
it
ona
clean
surface.
>
Then
install
the
alignment
pin
from
the
vehicle
tool
kit
in
the
empty
wheel
bolt
hole
by
hand
>
fig.
178.
>
Remove
the
rest
of
the
wheel
bolts.
Remove
the
wheel
>().
The
alignment
pin
re-
mains
in
the
hole
while
doing
this.
Installing
a
wheel
Read
the
directions
on >
page
266
when
instal-
ling
unidirectional
tires.
>
Slide the
wheel
on
over
the
alignment
pin
>@.
>
Install
the
wheel
bolts
and
tighten
them
gently
using
the
hex
socket.
>
Remove
the
alignment
pin
and
tighten
the
re-
maining
wheel
bolt.
>
Carefully
lower
the
vehicle
using
the
vehicle
jack*.
>
Tighten
the
wheel
bolts
in
a
diagonal
pattern
using
the
wheel
wrench*.
265

Use of Cookies    Contact us