2020 Audi Q5 / SQ5 — Owner's Manual – Page #373

Posted on 29 Nov, 2019
Model: 2020 Audi Q5 / SQ5
Pages: 412


File size: 111 MB

Download Manual

Online Viewer
80A012721B)
Emergency
assistance
ZA\
WARNING
—To
reduce
the
risk
of
injury,
make
sure
no
one
is
in
the
vehicle
before
raising
it.
Make
sure
the
vehicle
jack
is
stable.
The
risk
of
injury
is
increased
when
the
ground
is
slippery
or
soft,
because
the
vehicle
jack
could
slide
or
sink.
Only
raise
your
vehicle
with
the
vehicle
jack
provided
by
the
factory.
If
you
use
a
vehicle
jack
designed
for
another
vehicle,
your
vehi-
cle
could
slip
and
cause
injury.
Position
the
vehicle
jack
only
at
the
desig-
nated
mounting
points
on
the
side
sill
and
align the
jack.
Otherwise,
the
vehicle
jack
could
slip
and
cause
an
injury
if
it
does
not
have
sufficient
hold
on
the
vehicle.
To
reduce
the
risk
of
injury,
do
not
raise
any
other
vehicles
or
other
loads using
the
vehi-
cle
jack
provided
by
the
factory.
vehicles
with
air
suspension:
Changes
in
temperature
or
load
can
affect
the
height
of
the
vehicle.
To
reduce
the
risk
of
an
accident,
never
start
the
engine
when
the
vehicle
is
raised.
—To
reduce
the
risk
of
injury,
no
work
should
be
performed
under
the
vehicle
while
it
is
raised.
@)
Note
Do
not
lift
the
vehicle
by
the
sill.
Position
the
vehicle
jack
only
at
the
designated
mounting
points
on
the
side
sill.
Otherwise,
your
vehicle
could
be
damaged.
Removing
and
installing
a
wheel
g
=
x
oO
oO
Fig.
282
Wheel:
internal
hex
socket
to
turn
the
wheel
bolts
6
is
+
4
0
a
Fig.
283
Wheel:
alignment
pin
in
the
top
hole
Removing
a
wheel
>
Remove
the top
wheel
bolt
completely
using
the
hex
socket
in
the
screwdriver
handle
from
the
vehicle
tool
kit
>
fig.
282
and
place
it
ona
clean
surface.
>
Then
install
the
alignment
pin
from
the
vehicle
tool
kit
in
the
empty
wheel
bolt
hole
by
hand
>
fig.
283.
>
Remove
the
rest
of
the
wheel
bolts.
>
Remove
the
wheel
>().
The
alignment
pin
re-
mains
in
the
hole
while
doing
this.
Installing
a
wheel
Read
the
directions
on
page
372
when
instal-
ling
unidirectional
tires.
>
Slide the
wheel
on
over
the
alignment
pin
>@.
>
Install
the
wheel
bolts
and
tighten
them
gently
using
the
hex
socket.
>
Remove
the
alignment
pin
and
tighten
the
re-
maining
wheel
bolt.
>
Carefully
lower
the
vehicle
using
the
vehicle
jack*.
>
Tighten
the
wheel
bolts
in
a
diagonal
pattern
using
the
wheel
wrench.
The
wheel
bolts
must
be
clean
and
loosen
and
tighten
easily.
Check
the
contact
surfaces
for
the
wheel
and
hub.
Contaminants
on
these
surfaces
must
be
removed
before
installing
the
wheel.
Z\
WARNING
Read
and
follow
the
important
information
and
notes
under
>
page
348.
Never
use the hex
socket
in
the
screwdriver
handle
or
the hex
socket
wrench
with
the
ratchet
to
loosen
or
tighten
the
wheel
bolts.
This
increases
the
risk of
an
accident,
>
371

Use of Cookies    Contact us