2020 Audi Q7 — Owner's Manual – Page #281

Posted on 16 Feb, 2020
Model: 2020 Audi Q7
Pages: 316


File size: 114 MB

Download Manual

Online Viewer
4M1012721BA
Emergency
assistance
ZA\
WARNING
A
drained
battery
can
freeze
at
tempera-
tures
around
32
°F
(0
°C).
If
the
vehicle
bat-
tery
is
frozen,
it
must
be
thawed
before
con-
necting
the
jump
start
cables.
If
it
is
not,
the
risk
of
an
explosion
and
chemical
burns
increases.
After
jump
starting
the
vehicle,
drive
to
an
authorized
Audi
dealer
or
author-
ized
Audi
Service
Facility
immediately
to
have
the
vehicle
battery
checked.
Read
the
warnings
when
working
in
the
en-
gine
compartment
>
page
233.
Handling
the
jump
start
cables
incorrectly
may
cause
the
vehicle
battery
to
explode
and
lead
to
serious
injuries.
()
Note
Jump
start
cables
can
cause
considerable
damage
to
the
vehicle
electrical
system
if
they
are
connected
incorrectly.
@
Tips
There
must
be
no
contact
between
the
vehicles,
or
else
voltage
could
flow
when
connecting
the
positive
terminal
and
drain
the
vehicle
battery
of
the
vehicle
providing
the
jump
start.
The
drained
vehicle
battery
must
be
con-
nected
correctly
to
the
electrical
system.
Switch
off
electrical
equipment
that
is
not
needed.
Jump
starting
Both
jump
start
cables
must
be
connected
in
the
correct
order.
Fig.
187
Engine
compartment:
connectors
for
jump
start
cables
or
a
charger
Fig.
188
Connecting
the
jump
start
cables
The
jump
start
cable
connections
are
located
in
the
engine
compartment.
Follow
the
information
about
the
vehicle
battery
=>
page
242.
Connecting
the
positive
cable
(red)
to
the
positive
terminal
>
Open
the
red
cover
on
the
positive
terminal
>
fig.
187.
1.
Attach
one
end
of
the
positive
cable
(red)
to
the
jump-start
pin
@
©
fig.
188
on
your
vehi-
cle.
2.
Attach
the
other
end
of
the
positive
cable
(red)
to
the
positive
terminal
(2)
on
the
pow-
er
source.
Connecting
the
negative
cable
(black)
to
the
negative
terminal
3.
Attach
one
end
of
the
negative
cable
(black)
to
the
negative
terminal
@)
on
the
power
source.
4.
Attach
the
other
end
of
the
negative
cable
(black)
to
the
jump-start
pin
@
on
the vehi-
cle.
Starting
the
engine
>
Start
the
engine
in
the
vehicle
giving
the
charge
and
let
it
run
at
idle.
>
Now
start
the
engine
in
your
vehicle,
which
has
the
drained
battery.
>
If
the
engine
does
not
start,
stop
the
starting
procedure
after 10
seconds
and
then
repeat
it
after
approximately
30
seconds.
>
Turn
on
the
rear
window
defogger
in
your
vehi-
cle
in
order
to
reduce
any
voltage
peaks
that
may
occur
when
disconnecting
the
jump
start
cables.
The
headlights
must
be
switched
off.
279
>

Use of Cookies    Contact us